OSHA Training Requirements for Electrical Safety

Please note this is directly from OSHA. For your convenience we have highlighted the specific sections in orange to show type of training required and who’s required to be trained.

• Part Number: 1910
• Part Title: Occupational Safety and Health Standards
• Subpart: S
• Subpart Title: Electrical
• Standard Number: 1910.332
• Title: Training
• GPO Source: e-CFR

 

1910.332(a)

Scope. The training requirements contained in this section apply to employees who face a risk of electric shock that is not reduced to a safe level by the electrical installation requirements of 1910.303 through 1910.308.

Note: Employees in occupations listed in Table S-4 [see below] face such a risk and are required to be trained. Other employees who also may reasonably be expected to face comparable risk of injury due to electric shock or other electrical hazards must also be trained.

1910.332(b)

Content of training.

1910.332(b)(1)

Practices addressed in this standard. Employees shall be trained in and familiar with the safety-related work practices required by 1910.331 through 1910.335 that pertain to their respective job assignments.

1910.332(b)(2)

Additional requirements for unqualified persons. Employees who are covered by paragraph (a) of this section but who are not qualified persons shall also be trained in and familiar with any electrically related safety practices not specifically addressed by 1910.331 through 1910.335 but which are necessary for their safety.

1910.332(b)(3)

Additional requirements for qualified persons. Qualified persons (i.e. those permitted to work on or near exposed energized parts) shall, at a minimum, be trained in and familiar with the following:

1910.332(b)(3)(i)

The skills and techniques necessary to distinguish exposed live parts from other parts of electric equipment.

1910.332(b)(3)(ii)

The skills and techniques necessary to determine the nominal voltage of exposed live parts, and

1910.332(b)(3)(iii)

The clearance distances specified in 1910.333(c) and the corresponding voltages to which the qualified person will be exposed.

Note 1: For the purposes of 1910.331 through 1910.335, a person must have the training required by paragraph (b)(3) of this section in order to be considered a qualified person.

Note 2: Qualified persons whose work on energized equipment involves either direct contact or contact by means of tools or materials must also have the training needed to meet 1910.333(C)(2).

1910.332(c)

Type of training. The training required by this section shall be of the classroom or on-the-job type. The degree of training provided shall be determined by the risk to the employee.

  TABLE S-4. -- Typical Occupational Categories of Employees
    Facing a Higher Than Normal Risk of Electrical Accident
_________________________________________________________________________

                      Occupation
_________________________________________________________________________

Blue collar supervisors(1)
Electrical and electronic engineers(1)
Electrical and electronic equipment assemblers(1)
Electrical and electronic technicians(1)
Electricians
Industrial machine operators(1)
Material handling equipment operators(1)
Mechanics and repairers(1)
Painters(1)
Riggers and roustabouts(1)
Stationary engineers(1)
Welders
_________________________________________________________________________
 Footnote(1) Workers in these groups do not need to be trained if their
work or the work of those they supervise does not bring them or the
employees they supervise close enough to exposed parts of electric circuits
operating at 50 volts or more to ground for a hazard to exist.

Click here to view the OSHA Training Requirements for Electrical Safety on the OSHA website


The Jacman Group’s Arc Flash Training Courses are based on the NFPA 70E and designed to meet the OSHA electrical  training requirements. Click here for more information on the Arc Flash/NFPA 70E Electrical Safety Training.

Questions & Information

Contact us with any questions or for more information on the OSHA training requirements:

Call: 877-252-2626 | Email: info@jacmangroupsafety.com | Click here to contact us


Other helpful pages:     What is Arc Flash?     What is NFPA 70E?     Contact us